Details
| Originalsprache | Englisch |
|---|---|
| Seiten (von - bis) | 425-435 |
| Seitenumfang | 11 |
| Fachzeitschrift | Production Engineering |
| Jahrgang | 17 |
| Ausgabenummer | 3-4 |
| Frühes Online-Datum | 15 Sept. 2022 |
| Publikationsstatus | Veröffentlicht - Juni 2023 |
Abstract
The growing challenges regarding climate-neutral and resource-saving manufacturing technology is forcing research and development to work out new cutting tool alternatives since the production of conventional cutting materials requires rare raw materials and huge amounts of energy. Natural rocks could be such an alternative since they are available in large quantities worldwide, have a potentially suitable property profile, and do not require energy-intensive processes to make them usable as cutting material. However, according to the current state of knowledge, there are only a few studies on the usability and suitability of natural rocks as cutting materials for machining processes. Therefore, in this article, inserts made of natural rocks are ground and used in turning operations. Their operational behavior is then described by the occurring tool wear and workpiece surface roughness. The influence of different natural rocks, process parameters as well as cutting edge microgeometries is compared after the machining of aluminum alloys and plastic. In the end, this made it possible to define process and tool properties in which natural rocks have application potential.
ASJC Scopus Sachgebiete
- Ingenieurwesen (insg.)
- Maschinenbau
- Ingenieurwesen (insg.)
- Wirtschaftsingenieurwesen und Fertigungstechnik
Ziele für nachhaltige Entwicklung
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: Production Engineering, Jahrgang 17, Nr. 3-4, 06.2023, S. 425-435.
Publikation: Beitrag in Fachzeitschrift › Artikel › Forschung › Peer-Review
}
TY - JOUR
T1 - Tool wear when using natural rocks as cutting material for the turning of aluminum alloys and plastics
AU - Breidenstein, Bernd
AU - Denkena, Berend
AU - Bergmann, Benjamin
AU - Picker, Tobias
AU - Wolters, Philipp
N1 - Funding Information: The presented investigations were undertaken with support of the German Research Foundation (DFG) under Grant number 392377639. Funding Information: Open Access funding enabled and organized by Projekt DEAL. This work was supported by the German Research Foundation (DFG) under Grant number 392377639. The funders had no role in the design of this work, in the collection, analyses, and interpretation of the data, in the writing of the manuscript, or in the decision to publish the results.
PY - 2023/6
Y1 - 2023/6
N2 - The growing challenges regarding climate-neutral and resource-saving manufacturing technology is forcing research and development to work out new cutting tool alternatives since the production of conventional cutting materials requires rare raw materials and huge amounts of energy. Natural rocks could be such an alternative since they are available in large quantities worldwide, have a potentially suitable property profile, and do not require energy-intensive processes to make them usable as cutting material. However, according to the current state of knowledge, there are only a few studies on the usability and suitability of natural rocks as cutting materials for machining processes. Therefore, in this article, inserts made of natural rocks are ground and used in turning operations. Their operational behavior is then described by the occurring tool wear and workpiece surface roughness. The influence of different natural rocks, process parameters as well as cutting edge microgeometries is compared after the machining of aluminum alloys and plastic. In the end, this made it possible to define process and tool properties in which natural rocks have application potential.
AB - The growing challenges regarding climate-neutral and resource-saving manufacturing technology is forcing research and development to work out new cutting tool alternatives since the production of conventional cutting materials requires rare raw materials and huge amounts of energy. Natural rocks could be such an alternative since they are available in large quantities worldwide, have a potentially suitable property profile, and do not require energy-intensive processes to make them usable as cutting material. However, according to the current state of knowledge, there are only a few studies on the usability and suitability of natural rocks as cutting materials for machining processes. Therefore, in this article, inserts made of natural rocks are ground and used in turning operations. Their operational behavior is then described by the occurring tool wear and workpiece surface roughness. The influence of different natural rocks, process parameters as well as cutting edge microgeometries is compared after the machining of aluminum alloys and plastic. In the end, this made it possible to define process and tool properties in which natural rocks have application potential.
KW - Cutting tools
KW - Indexable inserts
KW - Natural rocks
KW - Turning
KW - Wear
UR - http://www.scopus.com/inward/record.url?scp=85138190191&partnerID=8YFLogxK
U2 - 10.1007/s11740-022-01159-2
DO - 10.1007/s11740-022-01159-2
M3 - Article
AN - SCOPUS:85138190191
VL - 17
SP - 425
EP - 435
JO - Production Engineering
JF - Production Engineering
SN - 0944-6524
IS - 3-4
ER -