Details
Original language | English |
---|---|
Journal | Vadose zone journal |
Volume | 13 |
Issue number | 1 |
Publication status | Published - Jan 2014 |
Abstract
Water repellency (WR) might affect the spatial and temporal dynamics of a wetting front during infiltration and redistribution in a way that is difficult to predict with standard approaches. Therefore, the objectives of this study were to simulate the wetting plume geometry with a three-dimensional numerical model and to test whether electrical resistivity tomography (ERT) is able to illustrate the geometry under highly dynamic conditions. At our study site under agricultural use (Gleyic Podzol, groundwater affected), persistent WR in the subsoil to the 120-cm depth was responsible for a conical plume geometry observed after ponded tracer application with Brilliant Blue (BB) and bromide. The process was invasively observed with hydraulic sensors. At the same time, ERT was used to monitor a second ponded infiltration event under equal boundary conditions at the same site. Numerical simulation of the process showed that hysteresis in the water retention curve is needed to describe the specific infiltration plume geometry correctly. The main wetting function was derived from scaling the main drying curve with measured contact angle data. A comparison of wetting front arrival times among the hydraulic model, sensors, and independent ERT observations indicates an overall good agreement and shows the usefulness of ERT measurements under highly dynamic in situ conditions. Our results confirm the need to include strong hysteresis effects scaled with independent contact angle data when simulating infiltration dynamics in a water repellent soil to avoid an underestimation of the wetting front arrival.
ASJC Scopus subject areas
- Agricultural and Biological Sciences(all)
- Soil Science
Cite this
- Standard
- Harvard
- Apa
- Vancouver
- BibTeX
- RIS
In: Vadose zone journal, Vol. 13, No. 1, 01.2014.
Research output: Contribution to journal › Article › Research › peer review
}
TY - JOUR
T1 - Hydraulic modeling and in situ electrical resistivity tomography to analyze ponded infiltration into a water repellent sand
AU - Ganz, Christina
AU - Bachmann, Jörg
AU - Noell, Ursula
AU - Duijnisveld, Wilhelmus H.M.
AU - Lamparter, Axel
N1 - Copyright: Copyright 2014 Elsevier B.V., All rights reserved.
PY - 2014/1
Y1 - 2014/1
N2 - Water repellency (WR) might affect the spatial and temporal dynamics of a wetting front during infiltration and redistribution in a way that is difficult to predict with standard approaches. Therefore, the objectives of this study were to simulate the wetting plume geometry with a three-dimensional numerical model and to test whether electrical resistivity tomography (ERT) is able to illustrate the geometry under highly dynamic conditions. At our study site under agricultural use (Gleyic Podzol, groundwater affected), persistent WR in the subsoil to the 120-cm depth was responsible for a conical plume geometry observed after ponded tracer application with Brilliant Blue (BB) and bromide. The process was invasively observed with hydraulic sensors. At the same time, ERT was used to monitor a second ponded infiltration event under equal boundary conditions at the same site. Numerical simulation of the process showed that hysteresis in the water retention curve is needed to describe the specific infiltration plume geometry correctly. The main wetting function was derived from scaling the main drying curve with measured contact angle data. A comparison of wetting front arrival times among the hydraulic model, sensors, and independent ERT observations indicates an overall good agreement and shows the usefulness of ERT measurements under highly dynamic in situ conditions. Our results confirm the need to include strong hysteresis effects scaled with independent contact angle data when simulating infiltration dynamics in a water repellent soil to avoid an underestimation of the wetting front arrival.
AB - Water repellency (WR) might affect the spatial and temporal dynamics of a wetting front during infiltration and redistribution in a way that is difficult to predict with standard approaches. Therefore, the objectives of this study were to simulate the wetting plume geometry with a three-dimensional numerical model and to test whether electrical resistivity tomography (ERT) is able to illustrate the geometry under highly dynamic conditions. At our study site under agricultural use (Gleyic Podzol, groundwater affected), persistent WR in the subsoil to the 120-cm depth was responsible for a conical plume geometry observed after ponded tracer application with Brilliant Blue (BB) and bromide. The process was invasively observed with hydraulic sensors. At the same time, ERT was used to monitor a second ponded infiltration event under equal boundary conditions at the same site. Numerical simulation of the process showed that hysteresis in the water retention curve is needed to describe the specific infiltration plume geometry correctly. The main wetting function was derived from scaling the main drying curve with measured contact angle data. A comparison of wetting front arrival times among the hydraulic model, sensors, and independent ERT observations indicates an overall good agreement and shows the usefulness of ERT measurements under highly dynamic in situ conditions. Our results confirm the need to include strong hysteresis effects scaled with independent contact angle data when simulating infiltration dynamics in a water repellent soil to avoid an underestimation of the wetting front arrival.
UR - http://www.scopus.com/inward/record.url?scp=84892992438&partnerID=8YFLogxK
U2 - 10.2136/vzj2013.04.0074
DO - 10.2136/vzj2013.04.0074
M3 - Article
AN - SCOPUS:84892992438
VL - 13
JO - Vadose zone journal
JF - Vadose zone journal
SN - 1539-1663
IS - 1
ER -